Wells M4200 Spezifikationen

CONVECTION OVEN WELLS MODELS WITH TOUCHPAD TEMPERATURE CONTROLLER/TIMERS M4200-3, M4200-3S This equipment chapter is to be inserted in the Oven sect

ITEM PART NO. DESCRIPTION QTY. FUNCTION 44 63873 Outer Heating Element (208 Volt Oven) 1 Heats the oven cavity interior and air. 63949 (240

ITEM PART NO. DESCRIPTION QTY. FUNCTION 53 65211 High-Limit Thermostat 1 Safety device which prevents excessive oven temperatures. 54 6384

ITEM PART NO. DESCRIPTION QTY. FUNCTION 58 63880 Relay 1 Turns the fan and heat OFF when the door is ajar. 59 63929 Transformer 1 Provid

ITEM PART NO. DESCRIPTION QTY. FUNCTION 66 63837 Outer Heater Gasket Cover 1 Protects and secures the heating element gasket in place. 67 64

ITEM PART NO. DESCRIPTION QTY. FUNCTION 73 63860 Door Top Hinge Bracket 1 Attaches the door to the oven and is used for door adjustment. 74

ITEM PART NO. DESCRIPTION QTY. FUNCTION *75 63912 Bottom Door Hinge Pin 1 Holds the door to the bottom hinge bracket assembly. 76 63900 Bo

ITEM PART NO. DESCRIPTION QTY. FUNCTION 79 65238 Air Duct Assembly 1 Thermal barrier to the rear exhaust vent. 80 63927 Thermocouple 1

HARDWARE IDENTIFICATION ITEM PART NO. DESCRIPTION TOTAL QUANTITY a 55618 4-40 Screw x 3/8" (10 mm) long 2 b 55496 4-Flat Washer 4 c 554

EQUIPMENT SET-UP AND CLOSE PROCEDURES Set-up 1. Make sure the power cord is plugged into the appropriate receptacle. 2. Place the 3 product racks

2. Place the ON/OFF/FAN switch in the ON or FAN position. 3. Verify that the time being displayed on the appropriate product cooking timer is corre

1CONVECTION OVEN Model M4200-3S PRODUCT FEATURES • Six-channel built-in timer. • Solid-state temperature controller with on-deman

CALIBRATION Tools: Digital Thermometer with Oven Probe; Oven Mitt. 1. Be sure the oven is plugged into the appropriate power supply receptacle. 2. O

19TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION ON/OFF/FAN switch is in the ON or FAN position and oven fails to operate. (No Red Power

PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Product is burning. Temperature set too high. Check temperature setting. Temperature controller out of

NOTE: The wiring diagram is located on the inside of the right side panel of the oven. In order to use it, the right side panel must be removed, but o

2. Using the phillips screwdriver, turn the 2 captive screws at the upper and lower left-hand side of the control panel until the panel is released.

6. Remove the thermostat capillary and bulb from the inside of the oven and remove the high-limit thermostat from the oven. (See Figure 5) NOTE: Adju

24 C. Repeat until the door ajar switch functions properly. NO

REPLACEMENT OF THE FAN MOTOR (Should be done by a qualified service person) Tools: Phillips Head Screwdriver, 5/32" (3 mm) Hex-Key Wrench, 8&quo

2, Using the phillips screwdriver, turn the 2 captive screws at the upper and lower left-hand side of the control panel until the panel is released. S

REPLACEMENT OF THE HEATING ELEMENT(S) (Should be done by a qualified service person) Tools: Phillips Head Screwdriver, 3/8" (10mm) Open End Wrenc

1a ELECTRICAL SPECIFICATIONS: VOLTS KW AMPS PER LINE THREE PHASE NEMA PLUG CONFIGURATION L1 L2 L3 208 7.5 20.8 21.8 21.8 L430P9

8. Remove the heating element(s) by pulling it straight out from the side of the cavity. 9. Reverse the procedure and use the wiring diagram to ins

ADJUSTMENT OF THE DOOR (TOP TO BOTTOM) Tools: Phillips Head Screwdriver, 10" (25 cm) . adjustable wrench. Parts: None. 1. Unplug the powe

30 DOOR TOO CLOSE TO THE GASKET - Loosen the 2 outer bolts and turn the center bolt COUNTERCLOCKWISE to bring the door away from the door gasket. Se

INSTALLATION INSTRUCTIONS For Converting an M4200 From 1 to 3 Phase 1. Warning: Be sure that all electrical power to the convection oven has been di

Installation Instructions For Converting an M4200 From I to 3 Phase 4. With step 3 completed, remove the existing plug and strip the black cord jac

2INTRODUCTION These commercial Convection Oven Models M4200-3 and M4200-3S are designed to bake food products uniformly and economically. They incor

ITEM PART NO. DESCRIPTION QTY. FUNCTION 1 21445 Prep-top Assembly 1 Pre-assembled parts no. 1A, 2, 3. 1A 63952 Prep-top (TOP) 1 Provides wo

4 ITEM PART NO. DESCRIPTION QTY. FUNCTION 11 63828 Prep-top mounting bracket (not on M4200-3S) 4 Brackets securing prep-top to the oven. 12

ITEM PART NO. DESCRIPTION QTY. FUNCTION 19 63827 Cord Hanger 1 Bracket for Power Cord storage. 20 63766 Rear Access Cover 1 Allows access

ITEM PART NO. DESCRIPTION QTY. FUNCTION 30 63817 Top and Bottom Door Gasket 2 Seal to retain the interior oven environment. 31 64504 Interi

ITEM PART NO. DESCRIPTION QTY. FUNCTION 35 63829 Heating Element Bracket 6 Holds the heating elements to the inner cavity. 36 63836 Inner